Acrylic splashbacks are an excellent choice to help you achieve a modern, stylish, and excellent looking finish to any room in your house. 

At SheetPlastics we offer an excellent range of acrylic splashbacks that are all designed and produced to your exact specification meaning all you have to do is simply put the panel in place and fit. We also offer a range of fixing accessories to assist you in your installation.


At Sheet Plastics we offer over 30 different colours and effects that you can choose from.


We offer a large selection of acrylic sheets in different effects and styles, we also offer a frosted finish which is proving popular for Kitchen Splashbacks. You can view our range of Frosted Acrylic Sheets here


Glass splashbacks are more expensive, will shatter, are susceptible to chipping and cracks and you are limited to colour selections in glass. Glass is much heavier than acrylic and more difficult to install.

Acrylic splashbacks are a cost effective, impact resistant, lightweight, easy to clean and maintain and easy to install product.


No, you cannot use acrylic behind the hob due to the fire rating of the acrylic sheet. People would normally use acrylic for the walls of the kitchen and behind the hob use steel, glass or our range of other materials mainly being our range of aluminium composite sheets. You can view our range of aluminium Composite products here


Because our range of acrylic splashbacks are produced using some of the best acrylic sheets from around the world our sheets are extremely easy to put to the wall and are easily attached to almost any surface.


We would recommend using 5mm thickness which will make the splashback more rigid but many people purchase from us daily 3mm and it is very rare we hear of any issues regarding installation or the rigidity of the panel.


Once you have decided what area you are looking at covering it is best to draw out on a piece of paper the area that is going to be covered and also include any parts that will require cut outs example sockets, wall units or cooker isolators.

If you are fitting your acrylic splashbacks to a surface between your worktop and a cupboard it is recommended to leave a 1mm top and bottom to ensure the panel fits but also ensures minimal movement. Also check that all worktop surfaces and cupboards are all level. These small gaps can be filled in later with sealant as you will want to prevent moisture from running down the walls and behind the splashback from the top.

Now measure the total width and height of acrylic needed and then mark it on your plan (remember to leave 1mm top and bottom). Measure where you need to cut around any cupboards, again leaving a slight gap for movement.

When it comes to sockets and switches, a gap between 3mm and 5mm is left around the cut out socket face sits inside it. Sealant can then be applied around the inside of the gap to seal the socket and the edge of the acrylic.

Now you have the measurements, our experts at Sheet Plastics offer a plastic splashback cut to size service for you. Get the experts at Sheetplastics.co.uk to machine cut your splashback to your exact specification or you can attempt to cut the materials and finishing yourself.

Cutting Acrylic Splashbacks for Kitchens

It is possible to cut your own splashback but it is recommended that your DIY skills are well above average.

You will need some tools which include drills and jigsaws.

Drills: You should only use drill bits made specifically for drilling acrylic. These are normally pre-ground twist bits. When drilling, make sure that you don't push the bit through the acrylic as it can burst through the bottom and cause sections to splinter off. Support the drill hole with a piece of timber and drill down into this to help stop any damage of this kind

Saws: Again, there are many specialist blades made for this job, so please make sure you use one of these. You can cut with a hand saw if you wish but using a jigsaw set on the fastest cutting speed will produce the cleanest, most uniform cut. Never force the blade through the material as it can overheat and cause the cut edge to melt. Also make sure that vibrations are kept to a minimum as these can cause cracks and splits. Laying the acrylic on top of cardboard while you cut it can help with this.

When you are cutting any straight lines with a jigsaw it is recommended to clamp a wooden batten or similar along the line you are cutting so the base plate of the jigsaw can follow it ensuring a straight line as a final result.

When you receive your sheet of plastic from www.sheetplastics.co.uk it will come with a protective film on both sides of the sheets. It is important that you leave this on until the sheet until it is ready to be secured to the wall.

Cutting acrylic splashbacks for kitchens can be difficult and it is important that you don’t let the acrylic overheat or it will melt, and also reduce vibration as much as is possible.

When cutting out holes for sockets, we recommend marking the exact area that needs cutting and use a jigsaw to cut this out. In order to get the blade in you can drill some large holes in each corner and then cut along the line from hole to hole. When drilling the initial holes make sure you drill them on the inside of the cut-out. Be careful to follow the marked-out lines. Otherwise your panel will not fit and you will either have to trim down bits which can be difficult with acrylic or you could even cut completely wrong and have to order the piece of acrylic again.

Assuming you have done all the above correct you should now have an acrylic splashback cut and ready to be fitted. Once you have cut outs in your acrylic you need to move it carefully, we would recommend getting some extra help to position your acrylic in place to make sure it fits. If you do need to make any small adjustments you can use a small file.

Smoothing The Edges of Your Acrylic Splashbacks

If you have used non specialist tools, you will more than likely have some jagged and sharp edges. So it’s time to smooth some of these edges.

To remove some of these edges you can use the flat edge of a suitably small half round file. But during this be very careful as now any damage to the sheets may be irreversible. The filing will remove the majority of major burrs but it is best to use some wet and dry paper to give the final finish.

When using the wet and dry paper, this will need to be done in several stages using several different grades of paper.

For the first pass, use something like a 100 - 120 grit paper, get a small bowl and fill with clean water. Dip the paper in the water and get it nice and wet. Wrap the paper around a small, flat piece of wood (to use as a rubbing block) and then proceed to rub the paper along the cut edge, keeping the block and paper flat to the edge of the acrylic. Again, do not apply much pressure and stop occasionally to clean the plastic shavings off the paper and also to wet the paper. Continue for several passes, up and down the full length of the acrylic.

For the second pass, swap the previous paper for something a little finer now, around 400 grit should be fine. Get the paper wet and then wrap around the block and repeat the above passes over the edge, stopping to clean the paper and re-wet periodically

For the final pass this time use a very fine paper. Something around 600 - 1000+ grit should be just right. Repeat the previous steps, checking the edge between passes to check progress. Once the edge is pretty much back to its smooth, shiny state you should be done. Again, check your passes regularly as you don't want to go too far and cause more damage.

Once you have got your cuts as smooth as possible using the wet and dry paper you can finish off by using T-Cut or similar. Dab a small amount on an old cloth and using your finger rub it along the edge. Using a clean cloth rub off misty residue to reveal your smooth and shiny edge.

Fitting Acrylic Kitchen Splashbacks

Now it is time to fit your acrylic splashback to the wall. Before doing this you need to make sure that the wall you are fitting the splashback to is completely flat and has no bumps or uneven parts as this could affect the final finish. With all the prep work done, now do a couple of tests to ensure that your splashback fits. Using the extra pairs of hands, place your splashback against the wall as if you were fitting to make sure that it all fits and all holes and cut outs fit.

Before applying any bonding to rear of the splashback remove the protective from the rear of the sheet. Clean the entire area with an Ispropyl Alcohol to remove all traces of dirt, dust, grime and grease. Once this has been done you can start using your chosen method of installation.

How to Fit Acrylic Kitchen Splashbacks 

There are a couple of methods of fitting your splashback to the wall: strong double-sided tape and silicon adhesive. We sell both of these products. If you are using double sided tape or silicon adhesive, we recommend that you purchase with your splashback a sample of the same colour and test in advance of the application. This is because some adhesives and tapes can be visible through some of the colours and, in particular, lighting will affect if the tape or adhesive can be seen. If you are using double sided tape, we recommend that you put this around all edges of the splashback and also in horizontal lines spacing them evenly ensuring they are no more than 300mm apart.

If you are using silicon do not put too close to the edge of the sheet as it will seep out when you apply to the wall. As with the tape, run beads of silicon horizontally across the sheet and space evenly ensuring they are no more than 300mm apart.

When you are ready to go, position the base of the splashback exactly where it needs to be in terms of position and angle at 45 degree from the bottom and start to push the sheet into the wall working upwards. The splashback will normally adhere to the wall very quickly but you may have to apply some pressure for a while. Total curing times if using adhesives is usually around 24 hours but check with the manufacturer’s instructions for confirmation.

Once cured and totally stuck remove the protective film from the sheet and admire your new plastic splashback.

NOTE: All of the above is general advice and should not be taken as a full instruction guide on how to measure, fabricate and install your splashback. Each application will vary with circumstances.

For the fabrication of your splashback we recommend you get it pre-fabricated by Sheet Plastics and then you either install yourself or seek the help of a local tradesman for the installation.

Benefits of using an Acrylic Splashback. 

  • Durable and impact resistant.
  • Easy to clean and maintain.
  • Colours will not fade. 
  • Food safe and hygienic
  • Produced from high quality materials
  • Lightweight
  • Will not shatter like glass.
  • Cost effective
  • Excellent aesthetic qualities 
  • Colour range available to match any colour scheme. 

To get a price for your acrylic splashback you can simply use our cut to size tool below, if you require fabrication on your acrylic splashbacks (cut outs, sockets and holes) then please email a basic drawing to bespokedesign@sheetplastics.co.uk and one of our expert staff will provide a quotation. You can find our guide to acrylic splashbacks here

Find your fantastic plastic. Try our Quick Quote Calculator. 3 Easy steps to order made to measure plastic sheets.

1. Select production type
2. Enter dimensions
3. Instant quote


Why Use Acrylic Panels

All of our acrylic sheets are impact resistant and shatterproof making them perfect for any use. As well as being lighter and more durable than glass, our clear acrylic sheets have clarity of 93%, greater than many common glass options.

Our mirrored and coloured acrylics are easy to clean making them ideal for splashbacks, giving your walls a modern feel whilst protecting them from anything that you can throw at them.

Our plastic sheets are available in a range of finishes including matte, clear and high gloss allowing you to choose a style to suit you, whether you’d 


Is perspex the same as acrylic?

Sheets of Perspex® are essentially just sheets or acrylic however ‘Perspex’ is a brand whereas an acrylic sheet is an item. There are many other brands of acrylic such as Plexiglass, Acrylite and Lucite.

Can you cut perspex?

Yes, Perspex is just a brand name for acrylic sheets which we have available in a huge range of designs available for custom cutting.

How big is a sheet of acrylic?

Our acrylic sheets are available in a range of sizes up to 3040mm x 2040mm. We can cut our plastic sheeting to your desired size to minimise cost and waste.

Is acrylic stronger than Perspex?

Perspex® acrylic sheet is a brand of acrylic sheeting that has an impact resistance 17 times stronger than glass. There is no difference in strength between Perspex and Sheet Plastics acrylic sheeting.

Is acrylic better to use than glass?

All acrylic sheets, and branded acrylic such as Plexiglass and Perspex, are more shatter-resistant, stronger, lighter and more resistant to erosion than glass.

Can you drill through acrylic?

Acrylic sheets, and branded acrylic such as Perspex, Plexiglass, Lucite, and Acrylite, require special drill bits to properly drill through them. Our drills are designed specifically for drilling into acrylic sheets, unlike normal metal drill bits which cause damages such as chipping and cracking.

How do you cut acrylic cleanly?

Our cutting machines are designed to get the smoothest cut possible from any acrylic however if desired we can also polish the corners to ensure a flawless finish.

If you would like to submit an enquiry to us, order a number of separate designs or would like further information on any of our products please contact us or fill in the form below

Fields marked with * must be filled in to submit your enquiry. Alternatively, call us on 01455240093

Enquire Online

 If you would like to submit an enquiry to us or would like further information on any of our products please fill in the form below
Fields marked with * must be filled in to submit your enquiry. Alternatively call us on 01455240093